Airaid 450-264 Manuel d'utilisateur télécharger pdf

Installation Instructions

For Part Numbers:

450-264 700-461 Airaid Oiled Media Filter

451-264 701-461 SynthaMax Dry Media Filter - Red

452-264 702-461 SynthaMax Dry Media Filter - Black

453-264 703-461 SynthaMax Dry Media Filter - Blue

2011-14 Ford Mustang GT

5.0L V8

2. A) Loosen the hose clamps on the factory intake

tube B) Squeeze the clamp and disconnect the resonator

from the air intake tube. C) Carefully depress the hose

lock tabs, and disconnect the crank case breather line

and the brake aspirator line (if equipped, AT models

only). D) Remove the factory intake tube.

3. A) Slide the r ed tab, and disconnect the wir ing har -

ness from the Mass Air Flow sensor (MAF). Carefully

pry the harness anchor from the air box using a screw-

driver. B) Separate the resonator tube from the stand off

attached to the Air box lid. C) Using a 10mm socket, re-

move the bolt securing the air box to the inner fender and

remove the air box assembly. This bolt will be reused in

step 9.

4. Install the Grommets and Fittings into the Airaid intake

tube (#2). A) All models will require the use of the 5/8”

Fitting (#19) and the 5/8”Grommet (#20). B) Automatic

transmission equipped vehicles will also use the 3/8” Fit-

ting (#18) and 3/8” Grommet (#21). Manual transmission

vehicles will not need the 3/8” components and will use

the Blind Grommet(#22).

5. Using the supplied Torx driver, remove the MAF sen-

sor from the Factory airbox and create the Tube assem-

bly.

A) Slide the Modular Ventur i Tube (#3) into the

Airaid intake tube (#2) making sure to align the two slots

for the MAF sensor. B) Install the MAF sensor into the

intake tube using two provided 8-32x3/8” screws (#12).

Do Not Use The Factory Screws!

6. Install the filter adapter (#8) using three 1/4-20 button

head bolts (#10), and flat washers (#11) into the Airaid

Cool Air Box (CAB) (#4) as shown.

Component Identification

1. Airaid Premium Filter 1

2. Airaid Intake Tube 1

3. Modular Venturi Tube 1

4. Cool Air Box 1

5. Urethane Hump Hose 1

6. Silicone Reducer 1

7. Urethane Cap* 1

8. Filter Adapter 1

9. Weather Strip 25” 1

10. ¼-20 Button Head Bolt 3

11. ¼” Flat Washer 3

12. 8-32 x 3/8” Button Head Bolt 2

13. #72 Hose Clamp 2

14. #64 Hose Clamp 1

15. #56 Hose Clamp 1

16. 60mm Hose Clamp 1

17. Firewall Plug* 1

18. 3/8”Aluminum Fitting 1

19. 5/8”Aluminum Fitting 1

20. 5/8”Grommet 1

21. 3/8”Grommet 1

22. Blind Grommet 1

23. #20 Torx Driver 1

Disconnect The Negative Battery Terminal!

1. Remove the Engine cover by simply lifting up, and

set aside.

7. Transfer the factory air box mounting grommets. A)

Locate and remove the Two Lower air box mounting

grommets, and install them in the inner fender. B) Re-

move the Upper air box mounting grommet and steel

sleeve, and re-install into the Airaid CAB.

8. Install the hump hose (#5) onto the filter adapter using

two #72 hose clamps (#13) as shown. Leave the two

hose clamps loose for now. Transfer the Resonator stand

off from the factory air box into the CAB.

9. Install the CAB into the vehicle. Make sure that the Air

inlet of the CAB aligns with the factory duct, and the two

locating pins on the bottom align with the factory grom-

mets. Next reinstall the factory bolt that was removed in

step #3 thru the steel sleeve and grommet and into the

inner fender.

1 2

Installation Instructions 1

Résumé du contenu

Page 1 - Installation Instructions

Installation Instructions For Part Numbers: 450-264 700-461 Airaid Oiled Media Filter 451-264 701-461 SynthaMax Dry Media Filter - Red 452-264 7

Page 2

Airaid Filter Co. 2688 E Rose Garden Ln. Phoenix AZ 85050 (800) 498-6951 [email protected] www.airaid.com P/N 790-551 Aerosol Spray P/N 790-5

Modèles reliés 451-264 | 452-264 | 453-264 |

Commentaires sur ces manuels

Pas de commentaire

Airaid 450-264 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Équipement aérien Airaid 450-264. Airaid 450-264 User Manual Manuel d'utilisatio

Résumé du contenu

Modèles reliés 451-264 | 452-264 | 453-264 |

Commentaires sur ces manuels

Produits connexes et manuels pour Équipement aérien Airaid 450-264