Airaid 510-302 Manuel d'utilisateur télécharger pdf

Installation Instructions

For Part Numbers:

510-302 700-462 Airaid Oiled Media Filter

511-302 701-462 SynthaMax Dry Media Filter - Red

512-302 702-462 SynthaMax Dry Media Filter - Black

513-302 703-462 SynthaMax Dry Media Filter - Blue

2010-15 Toyota 4Runner

2010-14 FJ Cruiser

4.0L V6

2. Remove the factory intake.

A.) Pry the wire harness anchor from the intake resona-

tor chamber

B.) Remove the 6mm anchor bolt from the resonator.

C.) Disconnect the crankcase breather and fuel pressure

regulator lines.

D.) Loosen the clamps on both ends of the intake tube

and remove the entire intake/resonator assembly.

3. Disconnect the Mas Air Flow sensor and remove the

factory airbox top and air filter.

4. Pry the wire harness anchor from the airbox. Remove

the three anchor bolts in the lower half of the airbox and

remove it from the vehicle. Remove the factory intake

tube bracket from the valve cover. It will not be reused.

5. Install the three M8 CAB Mounts (#13), hand tight,

into the weld nuts on the inner fender as shown. Note:

One of the original air box mounting holes is not re

used.

6. Apply the self adhesive, Foam Weatherstrip (#9) onto

the air inlet on the Cold Air Box (#3).

8. Transfer the Mass Air Flow sensor from the factory

airbox, into the Airaid Intake tube and secure using the

two #8 Spacers (#18) and 8-32 Socket Head screws

(#22) . Do not use the factory screws.

7. Mount the Filter Adapter (#5) to the Cold Air Box, as

shown, using three 1/4-20 x 1/2” Button head Bolts

(#16) and 1/4” Flat Washers (#17).

Component Identification

1. Airaid Premium Filter 1

2. Airaid Intake Tube 1

3. Cold Air Box 1

4. Air Box Lid 1

5. Filter Adapter 1

6. Hump Hose 1

7. Reducing Coupler 1

8. Airbox Gasket 1

9. Foam Weather Strip 1

10. 1/8 x 17” Vacuum Line 1

11. 1/8 NPT Barbed Fitting 1

12. 3/8 NPT Barbed Fitting 1

13. M8 CAB Mount 3

14. 8 mm x 1.25 x 16 Bolt 3

15. 5/16 Flat Washer 3

16. 1/4-20 x 1/2 Button Head Bolt 7

17. 1/4 Flat Washer 7

18. #8 spacer 2

19. #48 Hose Clamp 1

20. #64 Hose Clamp 1

21. #68 Hose Clamp 2

22. 8-32 Socket Head Screw 2

Note: Installation of this intake system requires

some minor trimming of the engine cover if it is

to be reused.

Disconnect The Negative Battery Terminal.

1. Remove the engine cover.

Lift up on the front of the engine cover to unseat the

mounting grommets and remove it from the vehicle.

SPACER

7. Mount the Cold Air Box onto the CAB Mounts us-

ing the three 8mm Bolts (#14) and 5/16 Flat Washers

(#15).

Not Used

Full color instructions can be viewed on our web site at Airaid.com. Use the Product Search function to find your part number, and click View Details.

1 2

Résumé du contenu

Page 1 - Installation Instructions

Installation Instructions For Part Numbers: 510-302 700-462 Airaid Oiled Media Filter 511-302 701-462 SynthaMax Dry Media Filter - Red 512-30

Page 2 - Tune-Up Kit!

Airaid Filter Co. 2688 E Rose Garden Ln. Phoenix AZ 85050 (800) 498-6951 [email protected] www.airaid.com P/N 790-551 Aerosol Spray P/N 790-5

Modèles reliés 511-302 | 512-302 | 513-302 |

Commentaires sur ces manuels

Pas de commentaire

Airaid 510-302 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Équipement aérien Airaid 510-302. Airaid 510-302 User Manual Manuel d'utilisatio

Résumé du contenu

Modèles reliés 511-302 | 512-302 | 513-302 |

Commentaires sur ces manuels

Produits connexes et manuels pour Équipement aérien Airaid 510-302