10. Install the Airaid Premium Filter (#1) on
the MAF adapter. Next install the weather
strip (#9) on the CAD as shown. Start at the
front, next to the radiator, and work your way
towards the back.
11. Stage II
For maximum airflow and aggressive sound
from your vehicle, proceed with installing the
Airaid Modular Intake Tube (#5). The MIT can
be added or taken off of the vehicle at any time
depending on your preference. If you choose
not to install the MIT, skip to step #19 below.
12. Disconnect breather hose from valve cover.
Disconnect 1/8” vacuum line, and 1/4” vacuum
line from the back of the factory intake tube.
13. Remove two 10mm nuts, and the beauty
cover from the top of the engine. Remove one
bolt thru the Adel clamp that holds the air con-
ditioning hose to the intake tube. Loosen hose
clamps on each end of the factory intake tube.
14. Remove the factory intake tube. 15. Install the hump hose (#7) on the MAF
adapter (#4) with two hose clamps (#11).
Install the reducer (#6), small end first, onto
the throttle body with two hose clamps (#10).
Leave the clamps loose for now.
16. Install the barbed fitting (#11) into the
MIT as shown, and then slide the 1/4”x4’
hose (#13) over the fitting.
17. Install the MIT (#5) into the hump hose
(#7), and then into the reducer (#6). Adjust the
MIT snugly against the throttle body, and
tighten all 4 hose clamps. Install the supplied
button head bolt (#18), and washer (#19), thru
the Adel clamp and into the MIT to hold the
air conditioning hose.
18. Install the vacuum tee (#13) into the
1/4”x4” hose (#14), and reconnect the factory
1/4” and 1/8” vacuum lines to the tee as
shown. Install the 1/2”x13” breather hose (#8)
onto the valve cover and to the MIT as shown.
19. Double check your work!
Make sure there is no foreign material in the intake path. Make sure all clamps, hoses, bolts,
and screws are tight.
20. Reconnect the negative battery cable!
Airaid Filter Co. 26
88 E Rose Garden Ln. P
hoenix AZ 85050
(800) 498
-6951 [email protected] www.airaid
.com
REV.01.06.14
P/N 790-551 Aerosol Spray
P/N 790-550 Squeeze Spray
Thank you for purchasing the Airaid Intake System. Contact Airaid @ (800) 498-6951 8:00 AM - 5:00 PM MST weekdays for questions regarding fit or instructions
that are not clear to you. Your Airaid Intake System was carefully inspected and packaged. Check that no parts are missing, or were damaged during shipping. If any parts are
missing, contact Airaid. The air filter element is protected from direct exposure to water and debris; care should be taken not to drive through deep water. WATER INGESTION
IS THE DRIVERS RESPONSIBILTY! The air filter is reusable and should be cleaned periodically.
FILTER IDENTIFICATION
700-458 Airaid Oiled Media 701-458 Airaid SynthaMax Dry Media - Red
702-458 Airaid SynthaMax Dry Media - Black 703-458 Airaid SynthaMax Dry Media - Blue
For your Oiled media filter we suggest
using the AIRAID Filter Tune-Up Kit!
Synthamax Air Filters do not require oil.
Service air filter as needed by cleaning
with common non-petroleum all-purpose
household cleaner and water. Simple
Green®, Formula 409® or equivalent
works great. Apply cleaner to outside of
air filter and allow to soak. Then flush
filter clean from the inside out with a gar-
den hose and repeat steps if necessary.
Do not apply high pressure water or air
to clean filter. Allow filter to air dry and
reinstall.
(2 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels