Airaid 883-262 Manuel d'utilisateur télécharger pdf

Installation Instructions

Part Number 883-262

Polaris Ranger Snorkel Kit

2009 XP 700 E.F.I.

2010 XP 800 E.F.I.

1. Lift the hood, secure it in the upright position, and

disconnect the battery or batteries.

2. In the passenger side firewall area, locate the foam

prefilter box and Loosen the hose clamp. Remove the

prefilter box and set it aside.

3. Mount the Snorkel Inlet to the Snorkel Tube (#1),

using the four Torx screws (#14) and a 90deg. Low Pro-

file Ratcheting Screwdriver.

4. Carefully insert the Airaid Foam Prefilter (#7) into

the Snorkel Inlet.

5. Install the Snorkel Screen (#4) onto the Inlet using the

four 8-32 Button Head Screws(15).

7. Preinstall the three Loop Clamps (#10) onto the right

front A pillar of the cage.

8. Attach the Snorkel Tube to the Loop Clamps using

three1/4-20 Button Head Bolts (#11), 1/4-20 Locknuts

(#12), and Flat washers (#13). Leave all hardware fin-

ger tight at this time to allow for proper alignment .

Advisory Note:

Please read these installation instruc-

tions in their entirety before begin-

ning the install process. Airaid strong-

ly recommends the use of Locktite®

242 Medium strength threadlocker on

all threaded fasteners.

Tools Required For Installation:

7/16” and 1/2” Wrenches. 10mm, 7/16”, and

1/2” Sockets. Utility knife

T-25 Torx driver and 5/32” Allen Wrench.

Ratchet & Extension. 1/8”& 5/16” Drill bits.

Dremel ® Rotary Tool

Center punch and Mallet Utility Knife

Phillips and Standard Tip Screwdrivers.

90deg. Low Profile Ratcheting Screwdriver

Locktite ® 242 or equivalent, and a roll of

masking tape

Thank you for purchasing the Airaid Intake System. Contact Airaid @ (800) 498-6951 8:00

AM - 5:00 PM MST weekdays for questions regarding fit or instructions that are not clear to you.

Your Airaid Intake System was carefully inspected and packaged. Check that no parts are missing,

or were damaged during shipping. If any parts are missing, contact Airaid. The air filter element is

protected from direct exposure to water and debris; care should be taken not to drive through deep

water. WATER INGESTION IS THE DRIVERS RESPONSIBILITY

9. Outside view of properly placed Snorkel and clamps.

1 2 3

Résumé du contenu

Page 1 - 2010 XP 800 E.F.I

Installation Instructions Part Number 883-262 Polaris Ranger Snorkel Kit 2009 XP 700 E.F.I. 2010 XP 800 E.F.I. 1. Lift the hood, secure it in

Page 2 - Double check your work!

12. Drill out the bolt holes starting with a 1/8 pilot hole and finishing with a 5/16” bit. 13. Trace the center oval onto the masking tape

Page 3 - Filter Service

23569141311101312111312154786.0001.000***CHECK SCALE BEFORE USING TEMPLATE***MARK HOLES WITHCENTERPUNCH, THEN DRILL USING 5/16" BIT (4X)ALIGN ALL

Commentaires sur ces manuels

Pas de commentaire

Airaid 883-262 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Accessoires d'air Airaid 883-262. Airaid 883-262 User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Accessoires d'air Airaid 883-262