Airaid 310-110 Manuel d'utilisateur télécharger pdf

Installation Instructions

For Part Numbers:

310-110 700-421 Airaid Oiled Media Filter

311-110 701-421 SynthaMax Dry Media Filter - Red

312-110 702-421 SynthaMax Dry Media Filter - Black

313-110 703-421 SynthaMax Dry Media Filter - Blue

1997-02 Jeep TJ 2.5L I4

1997-04 Jeep TJ 4.0L I6

Does Not Fit 2.4L

Component Identification

1. Splash Guard 1

2. Tube Assembly 1

3. Adapter Tube 1

4. Bolt ¼-20x1/2” 2

5. Long Bracket 1

6. Short Bracket 1

7. ¼” Washer 2

8. Nylon Wire Tie 1

9. ¼” Washer 8

10. Bolt ¼-20x5/8” 4

11. Nut ¼ -20 4

Full color instructions can be viewed on our web site at Airaid.com. Use the Product Search function to find your part number, and click View Details.

I DISCONNECT NEGATIVE (-) BATTERY CABLE.

II Remove air filter housing.

a) Loosen intake tube hose clamp at the air box lid. Separate from lid. FIG #1

b) Unclip the air box lid. Remove and set aside the lid and filter.

c) From underneath the fender, use a 10mm ratchet to remove the 3 (three) nuts that secure the air box base.

*Note: Unscrew the nuts from underneath and use an 8mm wrench to keep the top bolts from turning. FIG #2

III Assemble Airaid Tube

a) Bolt the two brackets to the Airaid tube using the shorter 1/4-20x1/2” bolts and washers. See FIG #3 Do not tighten

yet.

b) The longer bracket attaches to the front mount point.

IV Install Airaid Tube

a) Position tube in place of air box. See FIG #4

b) Locate and adjust Airaid brackets over the original air box mounting holes. Insert a 1/4-20x5/8” bolt and flat washer.

Into each mounting bracket.

c) On the opposite side, secure to the fender with a flat washer and nut.

V Install “Splash Shield”

a) Locate and test fit the mounting points. Remove the existing plastic fastener for the inside mount.

See FIG #5 - Then fasten the shield with 1/4-20x5/8 bolts and washers.

b) Tie Wrap is optional. Press into hole on the top rear of splash shield. Fasten to radiator strut rod.

VI Finishing up Airaid Installation.

a) Check for any foreign objects in the airflow path.

b) Reconnect battery cable. Double-check your work.

c) After one week of driving, check hardware and filter for tightness.

1 2

Résumé du contenu

Page 1 - Installation Instructions

Installation Instructions For Part Numbers: 310-110 700-421 Airaid Oiled Media Filter 311-110 701-421 SynthaMax Dry Media Filter - Red 312-110

Page 2 - Fig#4 Fig#5 Fig#6

Airaid Filter Co. 2688 E Rose Garden Ln. Phoenix AZ 85050 (800) 498-6951 [email protected] www.airaid.com P/N 790-551 Aerosol Spray P/N 790-5

Modèles reliés 311-110 | 312-110 | 313-110 |

Commentaires sur ces manuels

Pas de commentaire

Airaid 310-110 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Équipement aérien Airaid 310-110. Airaid 310-110 User Manual Manuel d'utilisatio

Résumé du contenu

Modèles reliés 311-110 | 312-110 | 313-110 |

Commentaires sur ces manuels

Produits connexes et manuels pour Équipement aérien Airaid 310-110